P2B14: Cylinder 3 Injection Pulse Offset Not Learned
The ECM has not yet learned the per-cylinder injection pulse offset for cylinder 3. Combustion equalisation between cylinders cannot be applied until adaptation completes.
What P2B14 means
P2B14 is a generic OBD-II powertrain code in the fuel & air group.
- Check engine light
- Usually on
- Emissions-related
- Yes — can fail inspection
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Common causes
- 01Adaptation lost after battery disconnect or ECM resetMost likely
- 02Injector replaced without learn procedurePossible
Can I drive with P2B14?
Usually yes, for a short time.
The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
Why we rate it moderate
- Turns on the check engine light
- Emissions-related: will usually fail an OBD inspection
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose P2B14
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just P2B14. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for P2B12, P2B16, P2B10, P2B18. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check live data
Watch the related sensor and actuator readings in live data (Fuel injector cyl 3, ECM) and compare them with expected values in the service information for your vehicle.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Adaptation lost after battery disconnect or ECM reset; injector replaced without learn procedure. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
P2B14 repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Fuel injector cyl 3
- ECM
P2B14 FAQ
What does P2B14 mean?
P2B14 means “Cylinder 3 Injection Pulse Offset Not Learned”. The ECM has not yet learned the per-cylinder injection pulse offset for cylinder 3. Combustion equalisation between cylinders cannot be applied until adaptation completes.
Is P2B14 serious? Can I keep driving?
We rate P2B14 as moderate severity. Usually yes, for a short time. The car will often drive normally, but get it diagnosed soon. Left alone it can raise fuel use and emissions and will fail an OBD inspection. If you notice rough running, warning lights flashing, overheating or a burning smell, stop driving.
What causes P2B14?
The most common causes, from most to least likely: Adaptation lost after battery disconnect or ECM reset; Injector replaced without learn procedure. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix P2B14?
Typical labor is about $40–$750 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix P2B14 myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will P2B14 clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.