U025C: Lost Communication With Special Purpose Vehicle Control Module D
The vehicle bus reports loss of communication with special-purpose vehicle (SPV) control module D. Upfit functions like emergency lighting, sirens, fleet relays or PTO/auxiliary systems controlled by this node stop responding.
What U025C means
U025C is a generic OBD-II network code in the lost communication group. In plain English: a control module stopped receiving messages from the Special Purpose Vehicle Control Module D on the vehicle’s data network.
- Check engine light
- Usually off
- Emissions-related
- No
- Limp mode possible
- Not typical
- Drive cycle to clear
- Required
Get it fixed
Post this code once and get quotes from local mechanics. Free to post.
Makes the repair and parts links below specific to your car. Kept in this browser only.
Symptoms
- Multiple warning lights may illuminate
- Affected modules may go into limp mode or shut down
- Specific functions inoperative depending on module
- Diagnostic tools may show communication faults
Common causes
- 01Bus wiring open or shortedMost likely
- 02Module without power or groundPossible
- 03Module failedPossible
Can I drive with U025C?
Generally yes.
This fault is unlikely to affect how the car drives. Fix it when convenient.
Why we rate it low
- Does not normally turn on the check engine light
- Needs a drive cycle to confirm a repair
Severity is our rule-based rating from the code’s flags in OBDex and the system it affects, not an inspection of your car. If the check engine light is flashing, or you notice overheating, low oil pressure, or brake or steering problems, stop driving and get help.
How to diagnose U025C
- 1
Confirm the code and save freeze-frame data
Read the codes with an OBD-II scan tool and note every code, not just U025C. Save the freeze-frame data (speed, load, temperature when the fault set) before clearing anything; it tells you when the fault happens.
- 2
Check for related codes first
Look for U025B, U025A, U0259. Related codes often share a cause; a circuit or sensor code usually needs fixing before a performance code like this one.
- 3
Check module power, ground and the data bus
Confirm the module named in the code has battery voltage, ignition feed and a good ground. With the battery disconnected, a healthy CAN bus usually measures about 60 ohms between CAN-High and CAN-Low at the OBD port. Inspect connectors for corrosion and pushed-out pins.
- 4
Test the likely causes in order
Start with the most likely cause and work down: Bus wiring open or shorted; module without power or ground; module failed. Test before replacing parts.
- 5
Check for recalls and service bulletins
Look up recalls for your exact vehicle with its VIN, and ask a dealer about technical service bulletins (TSBs). Manufacturers sometimes issue software updates or extended warranties for known faults.
- 6
Clear the code and verify the repair
After the repair, clear the code and complete a full drive cycle (cold start, idle, steady highway cruise, deceleration). The code is fixed when the related readiness monitor completes without it returning.
U025C repair cost estimate
Estimate, not a quote. Labor times are typical ranges for this code from OBDex, and $125/hr is an assumed rate. Shop rates and labor times vary by vehicle and region. Diagnosis time may be billed separately.
- DIY difficulty
- Moderate
- Good DIY job?
- Usually a shop job
Needs a scan tool and some experience with testing.
Parts and systems involved
- Special purpose vehicle module D
- Vehicle bus wiring
U025C FAQ
What does U025C mean?
U025C means “Lost Communication With Special Purpose Vehicle Control Module D”. The vehicle bus reports loss of communication with special-purpose vehicle (SPV) control module D. Upfit functions like emergency lighting, sirens, fleet relays or PTO/auxiliary systems controlled by this node stop responding.
Is U025C serious? Can I keep driving?
We rate U025C as low severity. Generally yes. This fault is unlikely to affect how the car drives. Fix it when convenient.
What causes U025C?
The most common causes, from most to least likely: Bus wiring open or shorted; Module without power or ground; Module failed. Test before replacing parts, because several causes can set the same code.
How much does it cost to fix U025C?
Typical labor is about $65–$500 at an assumed $125/hour shop rate, plus parts. That is an estimate, not a quote: labor times and rates vary by vehicle and region, and diagnosis may be billed separately.
Can I fix U025C myself?
DIY difficulty is moderate. Most owners leave this to a shop because it needs involved testing or specialist tools. Always confirm the cause before buying parts.
Will U025C clear itself?
Once the fault is fixed, the check engine light usually goes off by itself after the system passes its self-test over several drive cycles. Clearing the code with a scan tool resets readiness monitors, so an inspection station may turn you away until a full drive cycle is completed.